Clusters of blisters below or just above a GRP yacht's waterline are evidence of underwater blistering, but their appearance does not establish the cause or depth. Some damage remains at gelcoat level, while larger or deeper blisters can extend into the laminate and lead to laminate failure.
This guide explains how moisture enters GRP, what a survey must establish, and how the findings shape removal, drying, repair and barrier coating. It also covers the checks crew can make without trying to diagnose laminate condition from the surface.
What gelcoat blisters indicate
Polyester laminating resins and gelcoats are permeable rather than waterproof. Water can therefore migrate through cured resin. A blister develops when water accumulates within a void and hydraulic pressure rises beneath the surface.
Osmosis is part of that mechanism. It draws water into voids containing soluble material, increasing the volume of fluid and the pressure within the void until a blister forms.
The void may originate from entrapped air, a crack or dry fabric within the laminate. International Yacht Paint also identifies external water ingress, internal water ingress, including from bilges, and reactive resin impurities as possible root causes.
Higher laminate temperature increases the rate of moisture permeation. Warm-water operation is therefore relevant background when assessing a yacht in Mallorca, but it does not prove the cause of blistering on a particular hull.
The visible condition still matters. Numerous blisters below or just above the waterline are a recognised symptom. Ruptured blisters may seep liquid, while extensive craters, cracking, soft areas or suspected deeper damage require escalation rather than a cosmetic filling decision.
Reading the symptoms without over-diagnosing them
A surface inspection can locate damage, but it cannot determine reliably whether that damage stops at the gelcoat. Photographing and mapping the hull before washing or grinding gives the surveyor a record of the original pattern.
| Finding | What it may indicate | Correct next action |
|---|---|---|
| Numerous waterline blisters | Underwater blistering | Record and arrange a survey |
| Ruptured blisters | Fluid has escaped | Photograph before cleaning |
| Craters into laminate | Deeper damage is possible | Assess for removal and rebuilding |
| Cracks or soft areas | Suspected laminate failure | Stop surface-only classification |
| Standing water in bilges | Possible internal moisture source | Record it for the surveyor |
| Condensation on the hull | Unsuitable coating condition | Delay barrier-coat application |
Moisture assessment belongs within the survey process. A single moisture-meter number does not prove osmosis, and the fact sheet provides no universal reading at which a hull must be peeled or coated. The decision must distinguish a coating defect or gelcoat-level problem from osmotic or structural laminate damage.
That distinction controls the work scope. International Yacht Paint advises having a survey carried out before treatment because the repair changes substantially once blistering extends into the laminate.
From survey to peeling, drying and re-coating
The repair should follow the condition found after assessment and removal, not a standard cosmetic routine. The core sequence is straightforward, but the amount of material removed and rebuilt depends on depth.
- Survey the hull. Establish whether the damage is limited to gelcoat or extends into the laminate. Include the crew's blister map, photographs and record of internal moisture sources.
- Remove affected material. For gelcoat blistering, International Yacht Paint says full gelcoat removal will probably be needed. Where extensive blisters and craters extend into the laminate, removal may also include laminate layers.
- Clean and dry thoroughly. Cleaning and drying come before epoxy repair and barrier coating. Coating over an undried hull does not follow the repair sequence given by the opened manufacturer guidance.
- Rebuild where required. If the damage reaches into the laminate, the scope can become re-lamination and a constructional rebuild programme. This is materially different from replacing gelcoat over an otherwise sound laminate and may need coordination as part of yacht refit management.
- Apply the specified epoxy and barrier system. Film build and coat count must remain tied to the selected product instructions. For its own epoxy system, WEST SYSTEM recommends a minimum 20-mil barrier coat, normally built in five or six coats at room temperature. That figure is product-system guidance, not a universal specification for every hull or coating system.
Drying cannot be reduced to a fixed calendar period from the supplied guidance. Survey findings, the depth of removal and the requirement for thorough drying must determine when the hull is ready to move to the coating stage.
Application conditions also affect timing. WEST SYSTEM warns against starting an epoxy barrier coat too early after a cool night because ambient air can warm faster than the hull, causing condensation. Do not coat a condensating surface. Verify the hull condition and follow the instructions for the coating system being applied.
Planning the repair and launch timing
The reliable way to plan this work is to preserve the order of operations: survey, remove, clean, dry, rebuild if required, then apply the specified epoxy and barrier coating. A launch date should not force barrier coating to begin before the hull is dry or while condensation is present.
The initial survey also separates two very different yard scopes. Gelcoat-level blistering may require full gelcoat removal, cleaning, drying and re-coating. Blisters or craters extending into laminate can require removal of laminate layers, re-lamination and constructional rebuilding.
For that reason, the final work list should not be fixed solely from photographs taken while the yacht is afloat. Photographs are useful for arranging the inspection, but the treatment decision remains survey-led.
What crew can check safely
Crew can preserve useful evidence and identify possible internal water sources without opening blisters or deciding how deep the damage runs.
- Map the affected areas. During haul-out, photograph and mark clusters of blisters, cracks, craters or weeping fluid before washing or grinding changes their appearance.
- Inspect the bilges. Check for standing water and record any internal moisture source for the surveyor. Internal water ingress, including from bilges, is one of the possible causes identified by International Yacht Paint.
- Check for condensation. Do not begin epoxy barrier-coat application on a condensating hull. Confirm the hull condition and refer to the coating system instructions.
- Escalate rather than classify. Visible blisters should be reported for assessment. Crew should not try to determine laminate depth from surface appearance alone.
These checks support the survey, but they do not replace it. In particular, neither the number of visible blisters nor one moisture reading establishes whether the underlying laminate requires rebuilding.
When to call an engineer
Arrange technical assessment when the visible condition or proposed work goes beyond straightforward observation.
- Widespread or deteriorating damage. Call when blisters are numerous, ruptured or cratered, or when they appear with soft areas, cracks or suspected laminate failure.
- Diagnosis is uncertain. A moisture and survey assessment is needed when the scope must distinguish coating defects from osmotic damage or structural laminate damage.
- Material removal is proposed. Gelcoat peeling, controlled drying, laminate rebuilding and an engineered barrier-coat programme require a defined technical scope.
- The coating window is doubtful. Stop if the hull is condensating rather than applying the barrier system to meet a planned date.
Blueward Marine provides gelcoat, paint and antifouling services from Palma de Mallorca. Use the online service booking to describe the blistering and upload photographs, or call the 24/7 emergency line on +34 971 251 374.
Frequently asked questions
Are gelcoat blisters always structural osmosis?
No. Surface appearance alone cannot establish the depth or cause. Blistering may involve external water ingress, internal moisture sources or reactive resin impurities. A survey is needed to determine whether the problem remains within the gelcoat or extends into the laminate and requires rebuilding.
Does one high moisture reading prove hull osmosis?
No universal moisture-meter threshold is supplied in the opened guidance, so one reading should not determine the repair. Moisture assessment forms part of a survey used to distinguish coating defects and gelcoat-level blistering from osmotic or structural damage within the laminate.
Can epoxy barrier coating be applied after a cool night?
Not if condensation is present. WEST SYSTEM warns that ambient air may warm faster than the hull after a cool night, allowing condensation to form. Verify the hull condition before application and follow the selected coating system's instructions rather than starting solely to meet a launch schedule.
Sources and further reading
These references informed this guide. Follow the procedures and limits for the equipment installed on board.
